Eshop roka 2025 s vykurovacou technikou

90°-Bogen PRESS GAS - 42 mm IVAR.IVN20 GAS

Artikelnummer: IVNGAS20.42
Nicht bewertet Bewertungsdetails
50,55 € –20 %
Vykurovacia technika Oblúk 90° PRESS GAS - 42mm
50,55 € –20 % 40,44 € / St 32,88 € ohne MwSt. Grundpreis:
Internationale Zustellung
auf Lager beim Lieferanten

Detaillierte Informationen

Produktdetailbeschreibung

90° Bogen PRESS GAS - 42 mm

Hinweis: Maße der Fittings PRESS GAS 76,1, 88,9 und 108 mm auf Bestellung.

Häufig gestellte Fragen

  • Welches Werkzeug benötige ich für die Montage dieses Fittings? Press-Fittings erfordern spezialisierte Presszangen mit der richtigen Zangentyp (meistens mit B, F oder TH bezeichnet nach System) entsprechend der Maße und dem Typ des Fittings – ohne korrektes Werkzeug kann die Verbindung weder hergestellt noch geprüft werden.
  • Wie erkenne ich, dass die Verbindung korrekt gepresst wurde? Bei hochwertigen Press-Fittings ist ein Presseindikator vorhanden (z. B. Dichtungsring, der bei unvollständiger Presse ausläuft) – vor dem Verputzen in die Wand oder in den Estrich ist immer ein Drucktest des gesamten Systems durchzuführen.
  • Kann die Verbindung nach dem Pressen getrennt werden? Nein, im Gegensatz zum Schraubverschluss ist die Pressverbindung dauerhaft und erfordert zum Trennen das Abschneiden des Fittings und das Austauschen durch ein neues.
  • Muss die Montage von einem Fachmann durchgeführt werden? Ja, das Pressen der Fittings erfordert fachmännische Kenntnisse und korrekt kalibriertes Werkzeug – wir empfehlen, die Arbeit einem Heizungsbauer/Sanitärmeister zu überlassen, insbesondere bei Verbindungen, die in die Wand oder in den Estrich verputzt werden und keine spätere Kontrolle ermöglichen.

Zusätzliche Parameter

Kategorie: IVAR.IVN20 GAS - 90°-Bögen FF PRESS GAS
Verfügbarkeit: Auf Lager oder beim Lieferanten
Letzte Preisaktualisierung: 13.04.2026 1:10:37

Produktbewertung

Seien Sie der Erste, der einen Beitrag zu diesem Artikel schreibt!

Dieses Feld nicht ausfüllen

Wie würden Sie dieses Produkt bewerten? Wählen Sie 1 bis 5 Sterne, wobei 1 die schlechteste und 5 die beste Bewertung ist.

Diskussion

Dieses Feld nicht ausfüllen

Diskussionsübersicht

R Avatar des Autors 15.11.2026 15:43
Czy w przypadku kształtki PRESS GAS o średnicy 42 mm zalecane jest zastosowanie uszczelki O-ring typu HNBR, a czy połączenie to pozwala na ewentualne rozmontowanie i ponowne użycie po wykonaniu presowania?
A Avatar des Autors 15.11.2026 15:43
Tak, produkt ten wyposażony jest w żółtą uszczelkę O-ring wykonaną z materiału HNBR. Należy jednak pamiętać, że połączenie presowe jest trwałe i po jego zapięciu nie można go rozmontować – w razie potrzeby demontażu konieczne będzie przecięcie kształtki i wymiana jej na nową.
B Avatar des Autors 26.10.2026 12:57
Bună, am auzit că acest colier e pentru gaz. Pot să-l folosesc și pentru instalația de apă caldă din casă sau e doar pentru metan?
A Avatar des Autors 26.10.2026 12:57
Salut! Acest model este special conceput doar pentru rețelele de gaz (metan, biogaz, propan) și nu este recomandat pentru apă. Este fabricat din oțel inoxidabil rezistent la temperaturi între -20°C și +70°C, dar materialul garniturii este optimizat pentru gaze. Pentru apă îți recomandăm să cauți alte fitinguri din categoria noastră dedicate instalatiilor sanitare.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all „Made in Italy“.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

„Made in Italy“ adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all „Made in Italy“.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.